DokuWiki

You've loaded an old revision of the document! If you save it, you will create a new version with this data.

====== LPIC-1 / Linux+  Cheat Sheet ======

===== LX0-101 =====

==== 101 System Architecture 14% ====

===  101.1 Determine and Configure hardware settings (LCN-1 CTL-3) ===
  * Enable and disable integrated peripherals
  * Configure systems with or without external peripherals such as keyboards
   * Differentiate between the various types of mass storage devices
   * Set the correct hardware ID for different devices, especially the boot device
   * Know the differences between coldplug and hotplug devices
   * Determine hardware resources for devices
   * Tools and utilities to list various hardware information (e.g., lsusb, lspci, etc.)
  * Tools and utilities to manipulate USB devices
  * Conceptual understanding of sysfs, udev, hald, dbus
  * Terms: /sys, /proc, /dev, modprobe, lsmod, lspci, lsusb

===  101.2 Boot the System (LCN-2 CTL-5) ===
  * Provide common commands to the boot loader and options to the kernel at boot time
  * Demonstrate knowledge of the boot sequence from BIOS to boot completion
  * Check boot events in the log file
  * Terms: /var/log/messages, dmesg, BIOS, bootloader, kernel, init

=== 101.3 Change runlevels and shutdown or reboot system (LCN-2 CTL-5) ===
  * Set the default run level
  * Change between run levels including single user mode
  * Shutdown and reboot from the command line
  * Alert users before switching run levels or other major system events
  * Properly terminate processes
  * Knowledge of basic features of systemd and Upstart
  * Terms: /etc/inittab, shutdown, init, /etc/init.d, telinit

==== 102 Installation and Package Management 18% ====

=== 102.1 Design hard disk layout (Chapter 3) ===
  * Allocate filesystems and swap space to separate partitions or disks
  * Tailor the design to the intended use of the system
  * Ensure the /boot partition conforms to the hardware architecture requirements for booting
  * Knowledge of basic features of LVM
  * Terms: / (root) filesystem, /var filesystem, /home filesystem, swap space, mount points, partitions

=== 102.2 Install a boot manager (Chapter 5) ===
  * Providing alternative boot locations and backup boot options
  * Install and configure a boot loader such as GRUB Legacy
  * Perform basic configuration changes for GRUB 2
  * Interact with the boot loader
  * Terms: /boot/grub/menu.lst, grub.cfg and other variations, grub-install, MBR, superblock

=== 102.3 Manage shared libraries (Chapter 2) ===
  * Identify shared libraries
  * Identify the typical locations of system libraries
  * Load shared libraries
  * Terms: ldd, ldconfig, /etc/ld.so.conf, LD_LIBRARY_PATH

=== 102.4 Use Debian package management (Chapter 2) ===
  * Install, upgrade and uninstall Debian binary packages
  * Find packages containing specific files or libraries which may or may not be installed
  * Obtain package information like version, content, dependencies, package integrity and installation status (whether or not the package is installed)
  * Terms: /etc/apt/sources.list, dpkg, dpkg-reconfigure, apt-get, apt-cache, aptitude

=== 102.5 Use RPM and YUM package management (Chapter 2) ===
  * Install, re-install, upgrade and remove packages using RPM and YUM
  * Obtain information on RPM packages such as version, status, dependencies, integrity and signatures
  * Determine what files a package provides, as well as find which package a specific file comes from
  * Terms: rpm, rpm2cpio, /etc/yum.conf, /etc/yum.repos.d/, yum, yumdownloader

==== 103 GNU / Unix Commands	43%   ====

=== 103.1 Work on the command line (Chapter 1) ===
  * Use single shell commands and one line command sequences to perform basic tasks on the command line
  * Use and modify the shell environment including defining, referencing and exporting environment variables
  * Use and edit command history
  * Invoke commands inside and outside the defined path
  * Terms: ., bash, echo, env, exec, export, pwd, set, unset, man, uname, history

=== 103.2 Process text streams using filters (Chapter 1) ===
  * Send text files and output streams through text utility filters to modify the output
  * Using standard UNIX commands found in the GNU textutils package
  * Terms: cat, cut, expand, fmt, head, od, join, nl, paste, pr, sed, sort, split, tail, tr, unexpand, uniq, wc

=== 103.3 Perform basic file management (Chapter 4) ===
  * Copy, move and remove files and directories individually
  * Copy multiple files and directories recursively
  * Remove files and directories recursively
  * Use simple and advanced wildcard specifications in commands
  * Using find to locate and act on files based on type, size, or time
  * Usage of tar, cpio, and dd
  * Terms: cp, find, mkdir, mv, ls, rm, rmdir, touch, tar, cpio, dd, file, gzip, gunzip, bzip2, file globbing

=== 103.4 Use streams, pipes and redirects (Chapter 1) ===
  * Redirecting standard input, standard output and standard error
  * Pipe the output of one command to the input of another command
  * Use the output of one command as arguments to another command
  * Send output to both stdout and a file
  * Terms: tee, xargs

=== 103.5 Create, monitor and kill processes (Chapter 2) ===
  * Run jobs in the foreground and background
  * Signal a program to continue running after logout
  * Monitor active processes
  * Select and sort processes for display
  * Send signals to processes
  * Terms: &, bg, fg, jobs, kill, nohup, ps, top, free, uptime, killall

=== 103.6 Modify process execution priorities (Chapter 2) ===
  * Know the default priority of a job that is created
  * Run a program with higher or lower priority than the default
  * Change the priority of a running process
  * Terms: nice, ps, renice, top

=== 103.7 Search text files using regular expressions (Chapter 1) ===
  * Create simple regular expressions containing several notational elements
  * Use regular expression tools to perform searches through a filesystem or file content
  * The following is a partial list of the used files, terms and utilities: grep, egrep, fgrep, sed, regex(7)

=== 103.8 Perform basic file editing operations using vi (Chapter 5) ===
  * Navigate a document using vi
  * Use basic vi modes
  * Insert, edit, delete, copy and find text
  * Terms: vi, /, ?, h, j, k, l, i, o, a, c, d, p, y, dd, yy, ZZ, :w!, :q!, :e!

====  104 Devices, Filesystems, Filesystem Hierarchy 25% ====

=== 104.1 Create partitions and filesystems (Chapter 3) ===
  * Use various mkfs commands to set up partitions and create various filesystems such as: ext2, ext3, xfs, reiserfs v3, vfat
  * Terms: fdisk, mkfs, mkswap

=== 104.2 Maintain the integrity of filesystems (Chapter 3) ===
  * Verify the integrity of filesystems
  * Monitor free space and inodes
  * Repair simple filesystem problems
  * Terms: du, df, fsck, e2fsck, mke2fs, debugfs, dumpe2fs, tune2fs, xfs tools (such as xfs_metadump and xfs_info)

=== 104.3 Control mounting and unmounting of filesystems (Chapter 3) ===
  * Manually mount and unmount filesystems
  * Configure filesystem mounting on bootup
  * Configure user mountable removeable filesystems
  * Terms: /etc/fstab, /media, mount, umount

=== 104.4 Manage disk quotas (Chapter 4) ===
  * Set up a disk quota for a filesystem
  * Edit, check and generate user quota reports
  * Terms: quota, edquota, repquota, quotation

=== 104.5 Manage file permissions and ownership (Chapter 4) ===
  * Manage access permissions on regular and special files as well as directories
  * Use access modes such as suid, sgid and the sticky bit to maintain security
  * Know how to change the file creation mask
  * Use the group field to grant file access to group members
  * Terms: chmod, umask, chown, chgrp

=== 104.6 Create and change hard and symbolic links (Chapter 4) ===
  * Create links
  * Identify hard and/or soft links
  * Copying versus linking files
  * Use links to support system administration tasks
  * Terms: ln

=== 104.7 Find system files and place files in the correct location (Chapter 4) ===
  * Understand the correct locations of files under the FHS
  * Find files and commands on a Linux system
  * Know the location and propose of important file and directories as defined in the FHS
  * Terms: find, locate, updatedb, whereis, which, type, /etc/updatedb.conf

===== LX0-102 =====

==== 105 Shells, Scripting and Data Management 17%  ====

=== 105.1 Customize and use the shell environment (Chapter 9) ===
  * Set environment variables (e.g., PATH) at login or when spawning a new shell
  * Write BASH functions for frequently used sequences of commands
  * Maintain skeleton directories for new user accounts
  * Set command search path with the proper directory
  * Terms: /etc/profile, env, export, set, unset, ~/.bash_profile, ~/.bash_login, ~/.profile, ~/.bashrc, ~/.bash_logout, function, alias, lists

=== 105.2 Customize or write simple scripts (Chapter 9) ===
  * Use standard sh syntax (loops, tests)
  * Use command substitution
  * Test return values for success or failure or other information provided by a command
  * Perform conditional mailing to the superuser
  * Correctly select the script interpreter through the shebang (#!) line
  * Manage the location, ownership, execution and suid-rights of scripts
  * Terms: for, while, test, if, read, seq

=== 105.3 SQL data management (Chapter 9) ===
  * Use of basic SQL commands
  * Perform basic data manipulation
  * Terms: insert, update, select, delete, from, where, group by, order by, join

==== 106 User Interfaces and Desktops 8% ====

=== 106.1 Install and configure X11 (Chapter 6) ===
  * Verify that the video card and monitor are supported by an X server
  * Awareness of the X font server
  * Basic understanding and knowledge of the X Window configuration file
  * Terms: /etc/X11/xorg.conf, xhost, DISPLAY, xwininfo, xdpyinfo, X

=== 106.2 Setup a display manager (Chapter 6) ===
  * Turn the display manager on or off
  * Change the display manager greeting
  * Change default color depth for the display manager
  * Configure display managers for use by X-stations
  * Terms: /etc/inittab; plus xdm, kdm, and gdm configuration files

=== 106.3 Accessibility (Chapter 6) ===
  * Keyboard Accessibility Settings (AccessX)
  * Visual Settings and Themes
  * Assistive Technology (ATs)
  * Terms: Sticky/Repeat Keys, Slow/Bounce/Toggle Keys, Mouse Keys, High Contrast/Large Print Desktop Themes, Screen Reader, Braille Display, Screen Magnifier, On-Screen Keyboard, Gestures (used at login, for example gdm), Orca, GOK, emacspeak
==== 107 Administrative Tasks 20% ====

=== 107.1 Manage user and group accounts and related system files (Chapter 7) ===
  * Add, modify and remove users and groups
  * Manage user/group info in password/group databases
  * Create and manage special purpose and limited accounts
  * Terms: /etc/passwd, /etc/shadow, /etc/group, /etc/skel, chage, groupadd, groupdel, groupmod, passwd, useradd, userdel, usermod

=== 107.2 Automate system administration tasks by scheduling jobs (Chapter 9) ===
  * Manage cron and at jobs
  * Configure user access to cron and at services
  * Terms: /etc/cron.{d,daily,hourly,monthly,weekly}, /etc/at.deny, /etc/at.allow, /etc/crontab, /etc/cron.allow, /etc/cron.deny, /var/spool/cron/*, crontab, at, atq, atrm

=== 107.3 Localization and internationalization (Chapter 6) ===
  * Locale settings
  * Timezone settings
  * Terms: /etc/timezone, /etc/localtime, /usr/share/zoneinfo, environment variables (LC_*, LC_ALL, LANG, TZ), /usr/bin/locale, tzselect, tzconfig, date, iconv, UTF-8, ISO-8859, ASCII, Unicode

==== 108 Essential System Services 17% ====

=== 108.1 Maintain system time (Chapter 7) ===
  * Set the system date and time
  * Set the hardware clock to the correct time in UTC
  * Configure the correct timezone
  * Basic NTP configuration
  * Knowledge of using the pool.ntp.org service
  * Terms: /usr/share/zoneinfo, /etc/timezone, /etc/localtime, /etc/ntp.conf, date, hwclock, ntpd, ntpdate, pool.ntp.org

=== 108.2 System logging (Chapter 7) ===
  * Syslog configuration files
  * syslog standard facilities, priorities and actions
  * Terms: syslog.conf, syslogd, klogd, logger

=== 108.3 Mail Transfer Agent (MTA) basics (Chapter 9) ===
  * Create e-mail aliases
  * Configure e-mail forwarding
  * Knowledge of commonly available MTA programs (postfix, sendmail, qmail, exim) (no configuration)
  * Terms: ~/.forward, sendmail emulation layer commands, newaliases, mail, mailq, postfix, sendmail, exim, qmail

=== 108.4 Manage printers and printing (Chapter 6) ===
  * Basic CUPS configuration (for local and remote printers)
  * Manage user print queues
  * Troubleshoot general printing problems
  * Add and remove jobs from configured printer queues
  * Terms: CUPS configuration files, tools and utilities; /etc/cups; lpd legacy interface (lpr, lprm, lpq)

==== 109 Networking Fundamentals 23% ====

==== 110 Security 15% ====

Edit summary

Note: By editing this page you agree to license your content under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International

DokuWiki

Site Tools

Page Tools