Differences

This shows you the differences between two versions of the page.

--- notes:lpic-1_notes [2026/07/23 23:15]
191.241.55.200 old revision restored (2014/02/23 03:09)
+++ notes:lpic-1_notes [2026/07/24 20:10] (current)
216.73.217.13 old revision restored (2026/07/24 14:26)
@@ Line 27: / Line 27: @@
     * Enhanced Host Controller Interface (EHCI) - USB 2.0 - 480 MBps - high speed
     * Extensible Host Controller Interface (XHCI) - USB 3.0 - 4 GBps - super speed
-    * Wireless Host Controller Interface (WHCI) - Wireless USB 1.0 - 480 MBps
     * Effective speed is lowest speed of device, cable and hub
     * Classes of USB devices :
@@ Line 56: / Line 55: @@
   * Check boot events in the log file
   * Terms: /var/log/messages, dmesg, BIOS, bootloader, kernel, init
-== Notes ==
-  * Boot Loader (LILO or GRUB) launches the linux kernel, passing kernel parameters if needed (/etc/lilo.conf | /boot/grub/menu.lst | /boot/grub/grub.conf)
-  * Module options (as well as aliases and post-install and pre-remove actions) are stored in /etc/modules.conf .
-  * //dmesg// displays kernel messages logged at last system boot.
-  * // /var/log/messages // contains all syslog messages.
 === 101.3 Change runlevels and shutdown or reboot system (LCN-4 CTL-5) ===
@@ Line 71: / Line 64: @@
   * Knowledge of basic features of systemd and Upstart
   * Terms: /etc/inittab, shutdown, init, /etc/init.d, telinit
+<pagebreak>
-== Notes ==
-  * When linux boots, first process is the //init// process which selects and switches to default runlevel.
-  * Runlevels - 0=shutdown, 1/s/S=single-user_maintenance, 2=multi-user, 3=multi-user_no-X, 5=multi-user_with-X 6=reboot
-  * On Debian, 2 is default and 3,5 are not used. On Redhat, 3 is the default.
-  * /etc/rc script to change runlevels on redhat (also init/telinit script)
-  * /etc/rc.sysinit (Redhat) or /etc/init.d/rcS (Debian) - system init script launched by init before system daemons
-  * /etc/rc.local- local startup actions called at end of startup
-  * /etc/init.d contains startup/shutdown scripts for all system services
-  * /etc/rc0.d - /etc/rc6.d contain softlinks KNNservice or SNNservice specifying whether to start or stop services and in what order for that runlevel (done by init process). Kills done before starts.
-  * /etc/inittab contains "id:N:initdefault:" for default runlevel N
-  * //runlevel// shows current and previous runlevel
-  * //shutdown [options] time [warning message]//  - -f=fastboot -h=halt -r=reboot -F=force-startup-checks -k=just-send-warning . Time is "now" or "+N" in N minutes or absolute time e.g. 23:58.
 ==== 102 Installation and Package Management 18% ====
@@ Line 92: / Line 73: @@
   * Knowledge of basic features of LVM
   * Terms: / (root) filesystem, /var filesystem, /home filesystem, swap space, mount points, partitions
-==Notes==
-  * choosing a disk layout for linux depends on amount of disk space, purpose of the system, size of the system and backup strategy. Some general guidelines are
-    * If diskspace is limited, just /boot, / and /swap
-    * /boot is a separate 50MB partition because older kernels/BIOS require kernels under a 1024 cylinder limit.
-    * For larger systems keep / smaller/simpler to reduce risk of corruption.
-    * Can use separate partitions for /var (to isolate system logs), /tmp (to isolate tempfiles), /home (for backup and RAIDing of user's data)
-    * Using a separate partition for /usr allows it to be shared via read-only NFS which allows for saving space and easier maintenance of apps/updates.
-  * Superblock on filesystem contains critical metadata so multiple redundant copies are kept.
-  * Filesystems must be mounted (listed in filesystem table) before being accessible. /etc/fstab is a list of filesystems to mount on boot up.
-  * Master Boot Record on first 512 bytes of first sector of disk contains info on partitions and bootup. Can be backed up and restored with <code>
-dd if=/dev/hda of=~/mbr.txt count=1 bs=512
-dd if=~/mbr.txt of=/dev/hda count=1 bs=512
-</code>
-  * To backup/restore just the partition layout, use sfdisk <code>
-sfdisk -d /dev/hda > partition_backup.txt
-sfdisk /dev/hda < partition_backup.txt
-</code>
-  * Linux may also be booted from Live USB which allows for persistent modifications. If the BIOS does nto support this, a bootable CD can be used first.
-  * Swap space allows main memory to be temporarily copied to disk. As a starting point set swap to twice the memory size (at least the same size).
 === 102.2 Install a boot manager (LCN-5 CTL-5) ===
@@ Line 138: / Line 98: @@
   * Determine what files a package provides, as well as find which package a specific file comes from
   * Terms: rpm, rpm2cpio, /etc/yum.conf, /etc/yum.repos.d/, yum, yumdownloader
 ==== 103 GNU / Unix Commands 43%   ====

DokuWiki

Site Tools

Differences

Page Tools